Hotpoint Dryer – Error Code E3

Hotpoint – Error Code E3

Is your Hotpoint tumble dryer showing up with Error Code E3 on the screen?

What is a Hotpoint Error Code E3?

Error Code E3 on your Hotpoint tumble dryer typically indicates a problem related to the dryer’s heating system. This can mean that the dryer isn’t able to reach the required temperature to dry your clothes properly, possibly due to issues with the heating elements, thermostats, or airflow blockages that prevent proper heating.

Recommended solution/fix steps

To fix the E3 error on your Hotpoint tumble dryer, you can follow these steps:

1. Turn off the dryer: Before doing anything, make sure to turn off and unplug your dryer to ensure safety.
2. Check the lint filter: Remove and clean the lint filter to ensure there’s no blockage that’s preventing proper airflow.
3. Inspect the vent: Make sure the dryer vent is not kinked, blocked, or disconnected. Clean out any lint or obstructions you find.
4. Reset the dryer: Sometimes, simply resetting the dryer can clear the error code. Wait a few minutes after unplugging, then plug it back in and try running it again.
5. Check the heating elements and thermostats: If you’re comfortable with it and the problem persists, you might need to check the heating elements and thermostats for continuity with a multimeter. If any part is defective, it should be replaced.

If these steps don’t resolve the issue, it might be best to contact a professional technician or the Hotpoint customer service for further assistance, as the problem could be more complex and require specific parts to be repaired or replaced.

Troubleshooting to try

• Check that the dryer is still plugged into the power socket
• Check for a dirty filter or blocked vent
• Check your dryer door is properly closed
• Check your tumble dryer circuit breakers
• Check your tumble dryer belt if the drum isn’t turning
• Check your dryer door switch
• Check that your dryer is level and not excessively shaking
• Check that all hoses are securely attached

How to restart/reset/reboot your Hotpoint tumble dryer?

You may find your Hotpoint laundry dryer needs resetting if it starts to malfunction or isn’t responding to any input via your control panel. Resetting your tumble dryer re-starts the internal computer and can often restore the unit to normal working order. The exact instructions will vary depending on your model of Hotpoint tumble dryer.

Typically, this procedure will be:

1. Unplug it (or turn off power at the circuit breaker)
2. Wait some time for the electrical charge to clear out of the dryer (usually 1 to 5 minutes at most)
3. Power it up again.

Hotpoint Maintenance

When it comes to extending the life of your dryer, a little maintenance goes a long way. Regular care can help your dryer run more efficiently, cutting down on drying time and helping you save on utility bills. A clean dryer is also a safe dryer—one that is free from possible fire hazards. Stay on top of the little things and you can help ensure your dryer is performing optimally for years to come.

When you have finished using your dryer

• Unplug the machine from the power socket.
• Wipe around the door to remove any remaining condensation and foreign matter.
• Clear the lint filter and empty the water tank (if not set up to automatically drain).

Cleaning your dryer

• Before you start cleaning your dryer, ensure that it is disconnected from the power (ie unplug the machine from the power socket).

Clean the filter after each cycle

• The filter is an important part of your dryer: it accumulates lint and fluff that is formed while drying. When finished drying, clean the filter by rinsing it under running water or with your vacuum cleaner. Should the filter become clogged up, the airflow inside the dryer will be seriously compromised: drying times lengthen and you will consume more energy. It may also damage your dryer. The filter is found in front of the dryer trim. Do not use the dryer without replacing the filter.
• Pull the plastic grip of the filter upwards.
• Clean the filter and replace it correctly. Ensure the filter is fully located flush into the tumble dryer trim.

Empty the water container after each cycle

• Pull the container out of the dryer and empty it into a sink or other suitable drain. Replace the water container securely. Always check and empty the container before you start a new drying programme.
• When your dryer is new, the water container will not collect water until the system is primed. This will take 1 or 2 drying cycles. Once primed it will collect water during every drying cycle.

Cleaning the condenser unit

• Periodically (every month) remove the condenser unit and clean any build-up of fluff from between the plates by rinsing it under the tap with cold water. This should be done with cold water from the rear of the condenser
• Unplug the dryer and open the door. 2. Pull open the condenser cover
• Release the three catches by turning 90˚ counter-clockwise then pull on the grip and remove them from the dryer.
• Clean the surface of the seals and replace them with the arrows pointing upwards making sure that the catches have been secured.

Check the drum after each cycle

• Turn the drum manually in order to remove small items (handkerchiefs) that could have been left behind.

Cleaning the drum

• Do not use abrasives, steel wool or stainless steel cleaning agents to clean the drum.
• A coloured film may start to appear on the stainless steel drum, this may be caused by a combination of water and, or cleaning agents such as fabric conditioner from the wash. This coloured film will not affect the dryer’s performance.

Cleaning the dryer

• External parts in metal or plastic and rubber parts can be cleaned with a damp cloth.
• Periodically (every 6 months) vacuum the front air intake grille, to remove any build-up of fluff, lint or dust. Also to remove the accumulation of fluff from the front of the condenser and filter areas, clean occasionally with a vacuum cleaner.
• Do not use solvents or abrasives.
• Have your dryer checked regularly by authorised technicians to ensure electrical and mechanical safety.